A clamp-in valve is held by a nut that squeezes a rubber seal against the inside flange of the rim, so the joint is a metal-to-rubber seal rather than a thread. We publish an installation torque for three of our clamp-in series and deliberately publish none for the other three, and that difference is what this guide covers.

A clamp-in valve is a metal stem with a rubber seal ring compressed by a nut, with no rubber sleeve stretched over the rim hole, so the sequence and the torque matter more than the thread.
- The working sequence is: confirm the rim hole matches the valve, seat the stem square, fit the seal stack in order, tighten in two stages, apply the series torque, then check the seal before the tyre goes on.
- We publish a recommended installation torque for three of our clamp-in series: 100 to 125 in-lbs (12 to 15 N·m) for the V3-20 and TR540 on 9.7 to 10 mm holes, and 35 to 55 in-lbs (4 to 6 N·m) for the TR570 on 16 mm (.625″) holes.
- For our passenger car and light truck clamp-in series (TR416, MS525 and V-5) we publish no installation torque, so the value comes from the wheel maker.
- Our clamp-in valve range covers .453, .625 and .236 inch rim holes, and every metal valve is 100% leak tested.
The honest headline is that a clamp-in valve is easier to install than most people expect, but only if the order is followed. Get the order wrong and you will have a wheel that looks fine, holds air for a week, then goes flat on the motorway.
What a clamp-in valve actually is
Most tyre valves are described as three parts: the valve body, the valve core and the valve cap. That is correct for a rubber snap-in valve, and it is why people install a clamp-in metal valve with the wrong mental model. A clamp-in valve has no rubber sleeve stretched over the rim hole; it is a metal stem with a rubber seal ring compressed by a nut against the rim.
A rubber snap-in valve is fitted from inside the tyre, because the bead pressing the sleeve holds it in the hole. A clamp-in valve is fitted from the wheel side and does not rely on bead pressure.
The torque figures we publish, and what they apply to
Here is the part that surprises people. We publish a recommended installation torque for three of our clamp-in series, and none for the other three.
| Series | Application | Rim hole | Installation torque | Max inflation |
|---|---|---|---|---|
| V3-20 | Truck and bus with steel rim | 9.7–10 mm | 100–125 in-lbs (12–15 N·m) | Not published |
| TR540 | Truck and bus, Alcoa aluminium wheels | 9.7–10 mm | 100–125 in-lbs (12–15 N·m) | Not published |
| TR570 | Truck and bus, demountable and non-demountable | 16 mm (.625″) | 35–55 in-lbs (4–6 N·m) | Not published |
| TR416 | Passenger car and light truck | .453 and .625 inch | Not published | 130 PSI |
| MS525 | Passenger car and light truck | .453 inch | Not published | 130 PSI |
| V-5 | Passenger car and light truck | .453, .625 and .236 inch | Not published | 130 PSI |
Read that table carefully, because it holds the most useful fact in this article. The two 9.7 to 10 mm hole series take 100–125 in-lbs while the 16 mm hole TR570 takes 35–55 in-lbs. The bigger hole does not mean the higher torque: torque is set by the thread and the sealing stack, so a number carried from one series will not hold on another.
Where we publish nothing, it is not because the value is unimportant. The torque for a passenger car clamp-in valve is a property of the rim, stem, seal and fastener together, and that combination is specified by the wheel maker.
Step 1 — Confirm the rim hole matches the valve
A clamp-in valve does not stretch into its hole, it has to pass through it, so the clearance must exist before the valve arrives. Our clamp-in metal valves cover .453, .625 and .236 inch rim holes, and the hole is not something you measure to the nearest millimetre in a car park.
Check the hole on the wheel itself, not the tyre size. A 16 inch rim and a 15 inch rim can share the same tyre, and the valve hole does not follow nominal rim diameter. If the wheel is in service, look at the hole.
Step 2 — Seat the stem square and fully home
The stem passes through the rim from the inside and the sealing ring sits on the inner flange. A rubber valve is held by friction from the bead, a metal one is located by the stem itself.
Push the stem through until the seal ring is flat and square against the flange. If it is cocked the seal will not compress evenly and you get a leak on one side only. Seat it by hand, and if it will not go in square, stop and look at the hole.
Step 3 — Fit the seal stack in the published order
Every clamp-in valve we supply comes with a specified hardware set, and the order matters because each piece has a defined face. The V-5 series is published with a grommet, washer, nut and cap per item.
Fit the grommet, then the washer, then the nut, in that order, each piece flat against the part below. The washer is not optional: it spreads the nut load across the seal ring rather than a narrow band.
| Item | Effective length (mm) | Rim hole (mm / inch) | Grommet | Washer | Nut | Cap |
|---|---|---|---|---|---|---|
| TR5991B | 19 × 34 | 11.5 / .453 | HRG39 | RW8 | HN4 | AT |
| V-3 | 14 × 33 | 11.5 / .453 | HRG2x2 | RW5 | HN2x2 | ET/BT |
| V-5 | 14 × 48 | 11.5 / .453 | HRG2x2 | RW5 | HN2x2 | ET/BT |
| VS-8-45 | 16 × 53-45° | 11.5 / .453 | HRG1, HG2 | RW12 | HN2x2 | ET/BT |
| TR6008C | 17.5 × 34 | 16 / .625 | RG39 | RW8 | HN4x2 | DT |
| VS-6 | 11 × 40 | 6 / .236 | RG54 | RW8 | HN4 | ET/BT |
Step 4 — Tighten the nut in two stages
Tighten the nut by hand until it is properly engaged, then apply the torque in two stages. The first stage brings the nut down and starts the seal compressing evenly; the second completes it. Going straight to full torque with the nut still loose lets it pull off centre and load the seal unevenly.
Use a calibrated torque wrench, not an impact gun and not a length of tube on a socket. An impact gun applies a shock load the seal is not designed for and hides the reading you need. Our valve installation tools let the operator read the wrench without marking the rim, because a marked rim is rejected in most inspections.
Step 5 — Apply the torque published for that series
Now the value goes on. For the V3-20 and TR540 it is 100 to 125 in-lbs, which is 12 to 15 N·m. For the TR570 it is 35 to 55 in-lbs, which is 4 to 6 N·m. For TR416, MS525 and V-5 there is no figure, so the wheel maker’s value applies.
If the wheel is aftermarket and you have no documentation, a torque value written down by the tyre shop beats an assumed one, because at least it is a recorded decision. If you are fitting a series where we publish nothing, write the value applied on the job sheet.
Fitting valves to rims sits inside the tyre and rim dimensional standards rather than a standalone installation document. ISO 4000-2:2021 covers passenger car tyres and rims, Part 2: Rims, while the valve thread is standardised in ISO 4570:2002, which sets limit dimensions and tolerances for the 5V through 20V thread series. The core references in our tables, such as the 9002#, come from the European Tyre Rim Technical Organisation.
Step 6 — Check the seal before the tyre goes on
Inflate to the service pressure, check for a seep at the valve, then check the pressure again after a period. A properly seated valve holds pressure, and one that is not usually shows it quickly, because the leak path is at the rim hole.
Every metal valve we build is 100% leak tested before it leaves the factory, and our clamp-in valves use an EPDM rubber O-ring seal with brass chrome construction. None of that rescues a bad seat: a sound valve in a bad hole still leaks.
What usually goes wrong, and where
| Symptom | What it points to | Where to correct it |
|---|---|---|
| Slow leak, appears after a week or two | Seal ring cocked or not seated | Step 2, before the nut |
| Leak on one side of the valve only | Uneven seal compression | Step 2 |
| Seep that appears warm | Seal ring not properly compressed | Step 4, second torque stage |
| Nut will not start square | Rim hole burred or out of round | Step 1, check the hole |
Which clamp-in valve should you actually specify?
Published effective lengths differ by family. The passenger car and light truck range, published as the V-5, the TR416 and the MS525, runs from 33 mm on the V-3 to 70 mm on the PVR152, including 45° and 90° bent variants. The truck and bus series run longer: 41 to 119 mm across the V3-20 and the TR540, and 33 to 131 mm across the TR570. If you need a series not on that list, ask before ordering.
What to ask a supplier before you order
Most installation problems I see trace back to an under-specified order rather than a bad part. Four things on the enquiry remove most of them:
- The rim hole diameter, and whether the wheel is new or in service.
- The effective length needed, and whether the valve is straight or bent.
- The maximum inflation pressure the valve must be rated for, and the series, because the series decides if a torque figure exists.
- Whether the seal, washer, nut and cap are wanted as a matched set or fitted separately.
We would rather confirm a row with you than ship a fitment we cannot trace, and every valve carries a part number that ties back to the series table it was published under. Send us the machine, the wheel and the tyre size, and we will tell you which series fits and whether a torque figure comes with it.
A note on matching pressures. A valve rated to 65 PSI is not a limit on how hard you can inflate a tyre, it is the pressure the valve is designed to hold. Our rubber snap-in TR413 series is published at 65 PSI with a maximum rim thickness of 4 mm, the 600HP and 602HP for .453″ holes are rated to 80 PSI, and the 800HP and 802HP for .625″ holes reach 100 PSI.
Send your enquiry · → Tire valves · → Valve installation tools
Frequently Asked Questions
What torque should I use on a clamp-in tyre valve?
It depends on the series. We publish 100 to 125 in-lbs (12 to 15 N·m) for the V3-20 and TR540 on 9.7 to 10 mm valve holes, and 35 to 55 in-lbs (4 to 6 N·m) for the TR570 on 16 mm (.625″) holes. For TR416, MS525 and V-5 we publish none, so take the value from the wheel maker.
Can I install a clamp-in metal valve in any rim?
Only where the rim hole matches and the rim can carry the seal. Our clamp-in range covers .453, .625 and .236 inch rim holes, with effective lengths from 33 to 131 mm. The hole must exist, be round and clean enough for the seal to seat flat.
What is the difference between a clamp-in valve and a rubber snap-in valve?
A rubber snap-in valve is held by the tyre bead pressing a rubber sleeve over the rim hole, so it is fitted from inside the tyre. A clamp-in metal valve passes through the rim hole as a metal stem and is sealed by a rubber ring compressed by a nut against the inside flange, fitted from the wheel side.
Do clamp-in valves need a rubber grommet?
Yes, and the seal ring decides whether the wheel holds air. Our V-5 series is published with a grommet, washer, nut and cap per item, with part numbers such as HRG39, RG54, RW12 and HN2x2 depending on the valve. The washer spreads the nut load across the seal.
Why does my newly fitted wheel lose air after a week?
Almost always the seal, not the valve. A seal ring cocked when the stem was pushed through, or a nut taken to full torque in one movement instead of two, loads unevenly and can leak after heat cycles. If the wheel was in service, check the rim hole was not burred.
Can I fit a valve without removing the tyre?
Yes, with the right product. Our tool-free emergency valve installs from the outside of the wheel on a .453″ standard hole, with qualified EPDM rubber and a brass stem, in five minutes or less without removing the tyre. It is a roadside item, not a general fitment.
Bobby
Manager, Ningbo Fortune Auto Parts Manufacture Co., Ltd.
Founded in 1996, Fortune is now one of the leading professional manufacturers of wheel balance weights, tire valves, and tool accessories. My work at the desk is mostly fitment and order questions from distributors and importers, so this guide is built from the rim hole sizes, effective lengths, seal stack part numbers and torques published on our own pages.
Published 18 November 2026 · Last verified 18 November 2026 · The recommended installation torques of 100–125 in-lbs (12–15 N·m) for the V3-20 and TR540 series and 35–55 in-lbs (4–6 N·m) for the TR570 series, the 130 PSI maximum inflation pressures for the TR416, MS525 and V-5 series, the 65, 80 and 100 PSI rubber snap-in ratings, the rim hole diameters, effective lengths, grommet, washer, nut and cap part numbers and the 100% leak and ozone test statements were verified on 18 November 2026 against the Fortune V3-20, TR540, TR570, TR416, MS525, V-5, TR413 and high pressure series product pages and the tire valves category page. ISO 4570:2002 and the ETRTO core references are cited for valve thread and core standardisation. Installation sequence and failure causes reflect field practice. No price, cost, profit or margin figure appears in this article.
Post time: Nov-18-2026




