• bk4
  • bk5
  • bk2
  • bk3

How to Match a Wheel: Size, Bolt Pattern, Center Bore, and Offset

A practical guide for distributors, tire shops, and parts buyers

A wheel can be the right diameter and still be the wrong wheel. Diameter only says which tire bead the rim can accept. It does not say whether the wheel will locate on the hub, clear the brake, carry the load, or stay clamped.

Four measurements decide the short list before anyone talks about finish or price: rim size, bolt pattern, center bore, and offset. Brand names, a shared lug count, and a photograph do not replace them. The vehicle, wheel, and tire makers’ limits still outrank a catalog line.

What Has to Match

Check What it controls What it does not prove
Rim size Bead-seat diameter, nominal width, and flange family Bolt pattern, load, or brake clearance
Bolt pattern (PCD) Lug count and the circle those holes sit on Center bore, thread, or seat type
Center bore Whether the wheel can pass over the hub pilot That the wheel is centered, if the bore is larger
Offset (ET) Where the rim sits inboard or outboard of the hub face Fender, suspension, or caliper clearance

A wheel fails the job if any one of the four is wrong. Close is not a fit.

How to Read a Rim Size

ISO 4000-2 specifies the designation, contour, and dimensions of 5° tapered drop-centre rims used mainly on passenger cars. The vocabulary behind those markings comes from ISO 3911. In trade use, a size such as 15×6J is read in three parts:

1 15 is the nominal rim-diameter code, in inches. It has to match the diameter code of the tire.
2 6 is the nominal rim width, in inches, measured between the bead seats. It is not the overall width across the outside of the flanges.
3 J is a flange-contour letter for that drop-centre family. It is not a strength grade, a load rating, or a material.

A listing written 14×5.5, without a flange letter, still has to be read as diameter and width. Do not invent the missing letter. Do not treat 14×5.5 and 14×6 as substitutes because both are 14-inch rims. Width changes the tire’s approved rim range, and it also changes where the inner and outer flanges sit even when offset is unchanged.

The tire maker publishes a measuring rim and an approved width range for each tire size. A diameter match only gets the bead onto the correct seat. If the tire’s approved range does not include that rim width, the pair is not approved, whatever the bolt pattern says.

Bolt Pattern Is a Diameter, Not a Lug Count

ISO 3911 names this the pitch circle diameter of the bolt holes. Trade listings shorten it to PCD, bolt pattern, or bolt circle. 5×114.3 means five holes whose centers lie on a circle 114.3 mm across. The hole count and the diameter are both mandatory. Five lugs is not a pattern.

The same pattern is written several ways. 4×100, 4-100, and 4/100 are one statement. 5×114.3, 5-114.3, and 5/114.3 are one statement. The separator is typography, not a second specification.

Inch and metric names meet at 25.4 mm per inch. These are exact conversions, not approximate fitments:

Metric Inches Same pattern
4×101.6 4×4 Yes
5×114.3 5×4.5 Yes
5×120.65 5×4.75 Yes
5×127 5×5 Yes
5×139.7 5×5.5 Yes
6×139.7 6×5.5 Yes
8×165.1 8×6.5 Yes

Patterns that differ by a millimeter or two are not the same pattern:

Pair Gap Interchangeable
4×98 and 4×100 2.0 mm No
5×112 and 5×114.3 2.3 mm No
5×114.3 and 5×115 0.7 mm No
5×120 and 5×120.65 0.65 mm No
6×135 and 6×139.7 4.7 mm No

A wheel from the wrong member of one of those pairs may start onto the studs. That is not evidence that it fits. The seats will pull unevenly, and the studs carry a bending load they were not given.

On a four-lug or six-lug hub, PCD is the center-to-center distance between two opposite holes. A five-lug hub has no opposite hole. Measure the center-to-center distance between two neighboring holes and divide by 0.5878, which is the sine of 36°. A neighboring distance of about 67.2 mm is 5×114.3. About 65.8 mm is 5×112. The 1.4 mm difference on that short chord is the whole 2.3 mm gap. If the result is not an exact known pattern, measure again. Do not round a doubtful result onto the nearest popular number. A bolt-pattern gauge is safer than arithmetic done once, in a hurry, on a rusty stud.

Dual-drilled wheels exist. They are a specific product with two real patterns, not a reason to treat two close patterns as one.

Center Bore Locates the Wheel

ISO 3911 calls the large middle opening the centre hole diameter. Catalogs often mark it CB. It is the hole that has to pass over the hub pilot. It is not the bolt circle, and it is not the fastener thread.

Compare the wheel bore with the hub pilot:

  • Equal. The pilot can center the wheel before the fasteners are tightened. That is hub-centric location.
  • Larger. The wheel can go on, but the pilot no longer fills the hole. The wheel is then located by the fastener seats as they are tightened, unless a correctly sized hub-centric ring fills the gap. The ring’s outer diameter has to match the wheel bore, and its inner diameter has to match that hub. A ring does not repair a wrong PCD, a wrong offset, a low load rating, or a brake that will not clear.
  • Smaller. The wheel will not seat. Do not machine the bore or the pilot to force it.

An oversized bore is common on multi-application aftermarket wheels, because one bore can be made large enough for several hubs that share a PCD. Sharing a PCD does not mean those hubs share a pilot. A 5×114.3 wheel can be right for the studs and wrong for the center.

If the wheel rocks on the hub until the nuts are tight, stop and account for the gap. Tightening a loose wheel in a circle, instead of a star, is a common way to leave it clamped off-center. The vibration that follows is often blamed on balance. The mass of the tire is then orbiting the hub rather than rotating about it.

Offset Says Where the Rim Sits

ISO 3911 defines the position of the rim centreplane against the attachment face of the disc:

  • Inset. The rim centreplane is inboard of the attachment face. Inset is that distance.
  • Zeroset. The centreplane and the attachment face coincide.
  • Outset. The rim centreplane is outboard of the attachment face. Outset is that distance. Track, the distance between the centreplanes of the two tires on an axle, increases as outset increases.

Trade listings call the same idea offset, or ET, from the German Einpresstiefe. A positive ET is the inset case: ET45 means the attachment face is 45 mm outboard of the rim centreplane, and the rim sits inboard relative to a zeroset wheel of the same width. ET0 is zeroset. A negative ET is the outset case: the rim moves outboard, and track grows.

Two consequences follow:

  • On the same wheel width, a lower ET moves the whole rim outward. ET35 sits 10 mm farther out than ET45. Inner clearance to the brake grows by about 10 mm, and outer clearance to the fender shrinks by about 10 mm. Suspension travel and tire bulge still have to be checked. Neither number is in the ET figure.
  • The same ET on a wider wheel is not the same package. Widening a rim about its centerline adds half of the added width to each side. A buyer who keeps ET constant and adds an inch of nominal width has moved both flanges. Nominal width is the bead-seat width, so a backspace calculated from nominal width plus offset is only a guide. Flange height sits outside that nominal width.

An offset printed as a range is not an invitation to choose any number inside it. The wheel being sold has one offset. Ask for that value before comparing it with the hub, the caliper, and the fender at full lock and full bump.

The Four Numbers Are Not the Whole Job

After size, PCD, bore, and offset agree, these checks are still open:

  • Load. The load rating marked for that wheel must not be exceeded. A stronger tire does not raise the wheel’s rating. The assembly is limited by the lowest of the tire, the wheel, and the axle or hub.
  • Fastener seat, thread, and engagement. Conical, ball, and mag or flat seats are different. The fastener has to match the seat in the wheel, and the thread diameter and pitch have to match the stud or the hub. Engagement shorter than one thread diameter is an unsafe joint. Seat and thread selection is covered in Lug Nuts and Lug Bolts: Seat, Thread, and Length Selection.
  • Brake and suspension clearance. Offset and width describe position. They do not measure a caliper, a control arm, or a balance weight.
  • Tire approval. Use the tire maker’s approved rim width, load, and speed limits. Do not read a tire size printed beside a group of wheel rows as approval for every row in the group.
  • Valve and TPMS. A snap-in valve and a clamp-in valve do not use the same hole shape. The valve has to match the hole in that wheel. A sensor also has to clear the drop well. Matching the tire does not match the sensor.
  • Balance and hardware. A wheel weight, a valve, or a ring that was correct on the previous wheel is not automatically correct on this one.

Trailer Wheels Are a Different Duty

A trailer wheel is selected with the same four measurements, then held to a trailer load case. Special Trailer (ST) tires are built for trailer service. A passenger wheel that happens to share a bolt pattern is not a trailer wheel, and a passenger tire is not an ST tire.

The usable capacity is the lowest rating in the set. If the tire is uprated, the wheel and the axle still have their own limits. The wheel has to be acceptable for the tire’s load and cold inflation pressure. Those figures belong on the wheel marking or in the wheel maker’s confirmation. They should not be inferred from diameter.

Common trailer patterns are the same conversions as above: 5×114.3 is 5 on 4.5, and 6×139.7 is 6 on 5.5. Pattern is still not enough. Center bore and offset change by hub, including hubs that use the same PCD. Zero offset is common on some trailer wheels and is not a rule for all of them.

Installation Still Decides Whether the Numbers Work

The Tire Industry Association uses RIST for wheel installation: remove debris, inspect the parts, snug in a star pattern, and torque to the specification for that vehicle or wheel. A torque wrench does not create clamp load by itself. Dirt, paint, a damaged seat, or a crossed thread can show the right torque on a joint that is not clamped.

Use the instruction for the joint in front of you:

  • Passenger and light-truck conical or ball-seat studs are often specified dry. The installation sheet filed with NHTSA for one wheel program says threads must not be lubricated, that the fastener must match thread diameter, pitch, and seat, and that less than one stud-diameter of engagement is unsafe. Its seat warning is direct: use only the fastener compatible with the seat, or torque can be lost and the wheel can separate.
  • Hub-piloted commercial wheels are a different joint. The wheel or fastener maker may specify a small amount of oil on the flange-nut face. Do not copy that oil onto a dry passenger seat, and do not copy a dry-seat rule onto a joint whose maker requires oil.

Hand-start every fastener. If one does not start by hand, stop. Snug in a star or crisscross pattern. An impact tool can bring the wheel up to the hub, but it is not the final setting. Finish with a calibrated torque wrench, at the vehicle or wheel maker’s number. Do not publish one torque for every stud size. Recheck at the interval that maker specifies, commonly after the first short trip, because clamp load can settle.

How to Read One Catalog Line

Fortune’s wheel pages keep trailer wheels and a 14- to 18-inch steel-wheel listing in separate tables. The trailer table is rim size, PCD, center bore, offset, and a tyre-size note. The steel-wheel tables add an article number, an STS number, and a brand application. The pages used here do not print a load rating, a fastener seat, or a model year. A picture caption is not a specification row.

Two steel-wheel lines show why the four checks exist:

Art No. STS No. Size PCD ET CB Application as printed
X40862 S4410056 14×5.5 4-100 45 56.1 Acura, Honda, Mitsubishi
X40709 S5511470 15×6.0 5-114.3 7 70.6 Ford Ranger

Both are steel wheels in the same chapter. They do not share diameter, width, bolt pattern, offset, or center bore. The application cell is a brand list from that row. It is not a year-by-year fitment, and it does not mean every vehicle of that brand uses those numbers.

One trailer row is enough to show the other table. A 10×4.5 listing is printed with PCD 4×100, center bore 67.5 mm, and ET 0. No tyre size is printed on that row. Nearby rows do print a tyre size beside a group of PCD and offset choices. Use the tyre note as a starting hint, then confirm the tire maker’s approved rim and the actual offset of the part being supplied. Some trailer cells print an offset band, such as a range rather than one number. Quote the part’s own ET.

Common Mistakes

Buying the diameter. A 15-inch tire needs a 15-inch rim. The other three measurements are still open.

Calling every five-lug wheel `5×114.3`. Five lugs also come in 100, 108, 112, 120, 120.65, 127, and 139.7 mm, among others.

Rounding a close pattern. 5×112 and 5×114.3 are 2.3 mm apart. They are not a regional spelling of one size.

Ignoring a larger bore. The wheel can bolt up and still be off-center. A ring is a sized part, not a universal insert.

Treating ET as styling. Ten millimeters of offset is ten millimeters of wheel movement. On a wider rim, the flanges move even when ET is unchanged.

Reading a brand list as coverage. A printed application names brands associated with that line. It does not approve every year and model of those brands.

Carrying the old fasteners over. A new wheel can have a different seat, thickness, or bore. The previous nuts can show tight and still fail to clamp it.

Upgrading only the tire. Trailer capacity does not rise because a higher-load tire was mounted on the same wheel.

FAQ

Is `5×114.3` the same wheel as 5 on 4.5? The bolt pattern is the same. 114.3 ÷ 25.4 = 4.5. Center bore, offset, width, and load can still differ.

Can a hub-centric ring fix the bolt pattern? No. A ring fills a bore that is larger than the hub pilot. It does not move the bolt holes, change offset, or add load capacity.

What does a negative ET do? In ISO 3911 terms it is an outset wheel: the rim centreplane is outboard of the attachment face. Track increases. Clearance to the fender has to be checked, and so does clearance on the inboard side if the wheel is also wider.

Why can two 15×6 wheels both list a similar brand and still not interchange? Diameter and width can match while PCD, ET, and center bore do not. Compare the whole line, not the first number.

Does the catalog tyre-size note approve that tire? No. It records the size printed in the table. Approved rim width, load, and inflation come from the tire maker. Wheel load comes from the wheel marking or the wheel maker.

Which lug nut should be used? The one whose seat matches the wheel and whose thread matches the stud or bolt hole, with at least one diameter of thread engagement. Fortune’s nut and bolt families are selected on those points, not on hex size alone.

Should the studs be oiled? Only when the maker of that joint says so. Many passenger seat instructions say dry threads. Some hub-piloted commercial joints specify a measured amount of oil. Use the instruction for the hardware being installed.

Safety Note

This article is a selection guide, not an installation approval and not a fitment certificate for any vehicle named in a catalog application. Follow the vehicle, wheel, tire, and fastener makers’ instructions. Do not exceed the wheel load rating. Do not install a wheel whose fastener seat, thread, or engagement is wrong. If a measurement is uncertain, stop and remeasure before the wheel is quoted or mounted.

Sources


Post time: Nov-15-2026